Apple IPOD Touch 4 Dock / Power Port Replacement

Posted: January 1, 2013 in IPOD Touch Repair

Apple Ipod touch 4  some times doesn’t charge the battery or you are not able to connect it to iTunes.

There can be either Cable or Dock Port is the problem.

First try cable if that doesn’t work then  check the dock / Power Port of the Ipod if you see some kind of crack or pin bents . Then it is most likely a Dock / Power Port of your IPOD that is damaged.

How to Replace a Dock / Power Port ?

Before continue Reading I just want to tell you guys , I am not responsible for any damage or anything wrong happened to you or your things. I am sharing because I got 95% success rate in that. if you are not that expert just leave that to us by clicking HERE .

Skills Required:

1, Soldering skill is must.

2, Precision work Take your time .

3, Something like Opening an electronic product skill required.

4, ESD Protection is must because you are about to play with IC`S.

Components & Tools Required :

1, Soldering Iron

2, Flux, Solder, Wick.

3, Dock /Power Port Part for replacement click here to Buy from us.

4, Phillips Screw Driver, Tweezer, Cutter.

5, Hot Air Gun.

First Step:

Remove the upper glass screen gently . Open all screws . Pull the metal inner supporting sheet towards you from Bottom safely with taking care of Speaker glued with metal sheet, and the power/volume flex cable so that you won`t damage the pads/Tracks on the logic board. Just Extract the logic board out of whole shell while desoldering the battery ,speaker, volume/power flex cable.

The logic board will look like

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Second step:

As you can see from the previous pic, there is a metal shielding on the dock/Power port which is soldered  with logic board at two points.

One at right and other at left corner with big joint.

you need to cut this metal shielding first like this

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Now Remove the solder from one side (from two joints) like you are peeling a patato.

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Now continue with peeling remove second left joint.(remove the solder)

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Third Step:

After Removing the Metal shielding. Apply flux on whole the pins of dock connector and with soldering iron put a big blob of melting solder on the pins and revolve around on all pins so that the whole pins solder gets melted . like this:

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Now, Gently apply some force to push back the connector while in revolving process.In few seconds you will able to extract the dock port out of logic board. like this:

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Fourth Step:

Now its all-most done, take a long breath. just use a wick to wipe/ Remove the solder from the board.

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

so that you can able to see through the holes of the connector like this:

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Fifth Step:

Now put a new part in the logic board, and first solder the two bigger metal shielding joints with adjustment of part. like this:

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Final Step:

In Same way of removing pins , Apply sufficient flux and with a big blob soldering iron revolve through all pins in one go. not that fast so that solder enters into pin holes properly . Then its done. like this:

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

Now Testing time:

IPOD TOUCH 4 DOCK PORT REPAIR

IPOD TOUCH 4 DOCK PORT REPAIR

As we can see it is charging and connected with iTunes now. So we have successfully Replaced the dock/ Power port.

Cheers 🙂

Don’t Forget to leave us a comment click  here or at the top Right Corner with Comment Icon, if you like that just like us on Facebook .

if you need any other document just let us know. We do all Apple Product Repairs.

Author: Shobhit Saini

Advertisements
Comments
  1. Hello Web Admin, I noticed that your On-Page SEO is is missing a few factors, for one you do not use all three H tags in your post, also I notice that you are not using bold or italics properly in your SEO optimization. On-Page SEO means more now than ever since the new Google update: Panda. No longer are backlinks and simply pinging or sending out a RSS feed the key to getting Google PageRank or Alexa Rankings, You now NEED On-Page SEO. So what is good On-Page SEO?First your keyword must appear in the title.Then it must appear in the URL.You have to optimize your keyword and make sure that it has a nice keyword density of 3-5% in your article with relevant LSI (Latent Semantic Indexing). Then you should spread all H1,H2,H3 tags in your article.Your Keyword should appear in your first paragraph and in the last sentence of the page. You should have relevant usage of Bold and italics of your keyword.There should be one internal link to a page on your blog and you should have one image with an alt tag that has your keyword….wait there’s even more Now what if i told you there was a simple WordPress plugin that does all the On-Page SEO, and automatically for you? That’s right AUTOMATICALLY, just watch this 4minute video for more information at. Seo Plugin

  2. mestreseo says:

    very good info that is presented in this post. i prefer to read this kind of stuff. the quality of content is fine and the language is interesting. thanks for your kind support. mestreseo mestreseo mestreseo mestreseo mestreseo

  3. Compressa says:

    Thank you sooo much!!! You saved my iPod. I followed your steps with 100% success:).

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s